牌號 P3010           廠家(產地) 德國巴斯夫 
用途級別 耐高溫 耐化學品 玻璃纖維增強阻燃級      

Ultrason® P 3010 NAT | BASF | PPSU 物性表

Unreinforced, higher viscosity injection moulding grade, flameretardent and with improved chemical resistance.
Abbreviated designation according to ISO 1043-1: PPSU

典型數據

加工方法

注塑, 薄膜擠出成型, 異型材擠出成型, 片材擠出成型, 其它擠出成型, 吹塑, 熱成型

供貨形式

粒料

地區供應

北美, 歐洲, 亞太, 中南美洲, 中東/非洲

top

Processing Texts

注塑成型

PREPROCESSING
Pre/Post-processing, max. allowed water content: .02 %
Pre/Post-processing, Pre-drying, Temperature: 140 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 350 - 390 °C
injection molding, Melt temperature, recommended: 370 °C
injection molding, Mold temperature, range: 140 - 180 °C
injection molding, Mold temperature, recommended: 160 °C

Pretreatment
Drying temper ature: 130 - 150°C
Drying time: minimum 4h
recommended dryer: vaccum or dry air dryer
maximum moisture: 0,02 - 0,05%

Ultrason® can be injection molded by any type of machinery on the market, provided that the plasticizing unit and the mold temperature control system have been configured appropriately. The machinery manufacturer must be consulted if any doubts exist on the ability of various parts to withstand the high temperatures required (e.g. barrel, barrel he ad, bolted connections, etc.)

Long residence time in combination with high temperatures should be avoided e.g. by pump out material at regular intervals.
During extended interruptions, the barrel temperature should be lowered to about 250-280°C.

It has been found out that heating to the requested processing temperature and shutting down or lowering the temperature is best carried out in two steps.
First, the barrel temperatures are set at the lower processing temperat ure range for the particular thermoplastic (340 - 350 °C). As soon as these temperatures have reached a steady state, the material in the barrel is pumped out. Second, the barrel temperature can be set to the required processing temperature or the heaters can be shut down.

    德國巴斯夫（BASF）在熱可塑性工程塑料“ULTRASONE”系列中追加了新產品Polyphenyl Sulfone（PPSU）“ULTRASONE P”。ULTRASONE P的特點是：兼具該系列中Polyether Sulfone（PESU）“ULTRASONE E”的高熔融溫度和Poly Sulfone（PSU）“ULTRASONE S”的低吸水性，而且耐藥性也很出色。目前，已開始供應“ULTRASONE P3010”的透明產品樣品，今后還將依次上市白色和黑色的P3010。 

原來的高性能非結晶塑料存在接口部位受到沖擊應力時容易損壞的缺點。該公司進行的夏氏沖擊試驗結果表明，ULTRASONE P的耐沖擊性約為普通非結晶塑料的10倍。因此可在需要較強耐沖擊性的配管接頭和閥門上使用。 

可承受2000次的高溫蒸汽循環，可用高溫清洗、殺菌。另外，發生火災時也不易排放有害物質，因此該公司希望能夠在飛機的座套、燈罩、換氣閥及行李箱上使用該產品。（



        東莞市鼎鑫塑化原料有限公司長期代理銷售德國巴斯夫系列高品質工程塑料產品，以下產品長期現貨供應，價格優惠，質量百分之百保證！